+- How2pass.com Forums (https://www.how2pass.com/forum)
+-- Forum: Site & Products (https://www.how2pass.com/forum/forum-3.html)
+--- Forum: Site News & Issues (https://www.how2pass.com/forum/forum-7.html)
+--- Thread: Packet Tracer Labs (/thread-2376.html)
Packet Tracer Labs - forumsupport - 09-06-2024
We are adding the Packet Tracer Activity-based Lab Simulations to our CCNA 200-301 product. Please use this thread to post any issues/comments about these labs.
RE: Packet Tracer Labs - jsehart - 09-18-2024
That works!
I used How2Pass and Cisco's Packet Tracer to run simulations scenarios from How2Pass.
By doing that, I was able to pass my CCNA with a scoring in all areas 90 and above.
RE: Packet Tracer Labs - lhdsmanuel - 10-09-2024
Hello everyone!
Do you know if on the real CCNA exam, can we use the "?", to help us to find the next word of the command? or is it forbidden?
RE: Packet Tracer Labs - forumsupport - 10-10-2024
Yes, you can use ? as well as Tab key to complete your command.
RE: Packet Tracer Labs - yaboislevi - 12-16-2024
(09-06-2024, 08:36 PM)forumsupport Wrote: We are adding the Packet Tracer Activity-based Lab Simulations to our CCNA 200-301 product. Please use this thread to post any issues/comments about these labs.
Hello the following labs do not have a packet tracer sims that can be downloadable: Local User, NACL & DHCP Snooping Sim #1, Local User, NACL & DHCP Snooping Sim #2, and Local User, NACL and Security Sim. Will these be available soon or are they discontinued?
RE: Packet Tracer Labs - help_desk - 12-16-2024
(12-16-2024, 02:31 AM)yaboislevi Wrote: Hello the following labs do not have a packet tracer sims that can be downloadable: Local User, NACL & DHCP Snooping Sim #1, Local User, NACL & DHCP Snooping Sim #2, and Local User, NACL and Security Sim. Will these be available soon or are they discontinued?Cisco Packet Tracer doesn’t support some of the commands required for these simulations. We’re working on alternatives, but we’re not sure how long this will take. In the meantime, you can use network emulators such as Cisco CML or EVE-NG to get hands-on practice.
RE: Packet Tracer Labs - azgaellux - 10-28-2025
Hello. Under CCNA v1.0, the lab sim for LACP Configuration has errors for Task #4.
Entering command "switchport native vlan 746" after "interface port-channel 44" comes up as "% Unrecognized command".
Could you please go over all of the command entries and verify/correct the issues?
UPDATE: Here is what I got when figuring out the configuration. This completes the lab at 100%.
TASK 1
On SW1:
Sw1#conf t
Sw1(config)#interface range f0/1-2
Sw1(config-if-range)#switchport
Sw1(config-if-range)#channel-group 44 mode active
On SW2:
Sw2#conf t
Sw2(config)#interface range f0/1-2
Sw2(config-if-range)#switchport
Sw2(config-if-range)#channel-group 44 mode active
TASK 2 & 3
On SW1:
Sw1(config)#interface port-channel 44
Sw1(config-if)#switchport trunk encapsulation dot1q
Sw1(config-if)#switchport mode trunk
On SW2:
Sw2(config)#interface port-channel 44
Sw2(config-if)#switchport trunk encapsulation dot1q
Sw2(config-if)#switchport mode trunk
TASK 4
On SW1:
Sw1(config)#interface port-channel 44
Sw1(config-if)#switchport trunk native vlan 746
Sw1(config-if)#interface range f0/1-2
Sw1(config-if-range)#switchport mode trunk
Sw1(config-if-range)#switchport trunk native vlan 746
Sw1(config-if-range)#exit
On SW2:
Sw2(config)#interface port-channel 44
Sw2(config-if)#switchport trunk native vlan 746
Sw2(config-if)#interface range f0/1-2
Sw2(config-if-range)#switchport mode trunk
Sw2(config-if-range)#switchport trunk native vlan 746
Sw2(config-if-range)#exit
Verify Configuration on both switches
show etherchannel summary
show interfaces trunk
show interface port-channel 44
RE: Packet Tracer Labs - help_desk - 10-29-2025
We have fixed the command to "switchport trunk native vlan 746". We are sorry for the inconvenience. Thank you!
RE: Packet Tracer Labs - azgaellux - 11-26-2025
CCNA V1.1 Lab Sim "Allowed/Native VLAN & LACP Sim #2" does not register any commands in the results page, never reaching to 100% completion and staying at 0% even when correctly completed and the configuration is saved on each device.
Please fix the .pka file and re-upload.
Also, no .pka file available for download on "802.1Q Trunking, Native VLAN/LACP Configuration Sim" under CCNA V1.1 Lab
Under CCNA V1.0 Lab Sim, no .pka file available for the following:
- Local User, NACL and Security Sim
- Local User, NACL & DHCP Snooping Sim #1
- IPv4 and IPv6 Deployment Sim
- Local User, NACL & DHCP Snooping Sim #2
Trunking, Native VLAN/LACP Confi
RE: Packet Tracer Labs - help_desk - 11-27-2025
We checked the .pka file for “Allowed/Native VLAN & LACP Sim #2” and found no issues. Please ensure that you are following our exact solution of the sim and try again.
The simulations you mentioned do not have .pka files because they involve commands or technologies that are not supported by Packet Tracer.
Thank you!